Category: Home

In the event that you have have or have a physically-challenged or aged visitors in your house, you may want to install grab and security bars in showers and your bath-tubs. Even if this isn’t the situation, installing security bars will improve the value and marketability of your house for re-sale. This can be a fairly simple process that most do it-yourself-ers can handle having a few resources that are easily available.

By rapping on the dry wall over the tile locate and mark studs. You’ll hear a a definite variation between the strong sound of dry wall as well as the sound of dry wall above a stud. There are stud finders available that will make the work simpler, in case you are having having troubles.

Mark the tiles below your mark on the stud. Using an amount in the bubbles that are plumb as well as its orientation, make a pencil mark most of the way where the studs are down the tiles marking. This provides you with the most versatility in identifying where the studs intersect using a joint in addition to putting the grab-bars. Avoid creating the mark itself is tougher to wash that to the tile off. With respect to the orientation of the bar (horizontal, vertical, or angled) it is possible to get just a few screws on each and every end right into a stud.

Drill a hole in a joint where the stud to confirm the place has been marked by you. Use a-1/8inch drill-bit and drill right into a grout joint that is horizontal. When it is not coated by the grab bar this could be patched with grout.

Mark the rest of the holes for the grab bar. Using your preliminary marks as a startingpoint, contain the the grab bar in mark and place the three holes for every single end of the grab bar. In order that two holes in every single end is going to be over a stud, orient the bar. As these will be handled note the hole on every end that may not go right into a stud.

Drill holes a T each mark utilizing a ¼- tile masonry bit and inch glass. In the holes over studs, use A5/3 inch wood bit to produce a pilot hole to the studs. In the holes that aren’t in to studs, use the plastic anchors given the grab bar.

Place the grab bar within the holes and make certain they may be lined up by inserting the point-of a screw in to each hole. Caulk the back of the flange after which attach the grab bar utilizing the screws provided with the bar. These should beat least 1 ¾ inches long to penetrate a-T least 1inch of the stud, dry wall and the tile. Get screws with all complete and the sam-e sort head when they’re not enough.

A brand new coat of paint updates a space more rapidly than nearly any decorating method and brightens. Corners can show challenging because it is hard without obtaining streaks of paint, to achieve these using a paint-roller. The best paint brush paired using the proper technique lets you get a straight coat in every one of the corners with no need for time consuming touch-ups on the surfaces that are adjacent .

Stick a duration of painter’s tape on floor or the ceiling after the wall you’re painting. Use the tape flush to safeguard flooring or the ceiling as you paint the corners.

Grasp an paint brush close to the foot of the handle. Holding the brush close to the bristles offers more control to you as you paint.

Dip the brush to the paint, covering about one third of the bristles’ duration. The brush from the rim of the paint can therefore the extra paint off drips.

A 2 inch-wide swath across the fringe of of the corner, therefore the slim part of the bristles is close to the fringe of of the corner keeping the brush. Repeat of the corner on either side.

Paint the the rest of the wall using a paint-roller. Overlap the roller onto the fringe of of the swath since this can get paint, you have previously painted, however don’t drive it completely to the edge.

Remove the tape following the paint in the corner has dried and you’ve applied all required coats of paint of the painter.

If you’ve recently bought an older house, you might have inherited a less-than-stunning bathroom. Tub enclosure or a vinyl is a cost effective technique of hiding a worn out tile and tub, transforming the the area in a matter of hours. The enclosure spares you an extended bathroom remodeling task by merely covering on tile and the existing tub. Vinyl or enclosures need specific treatment to keep up their visual appearance, nevertheless. Prevent the buildup of soap scum by rinsing and cleansing the tub surround whenever it is used by you. Allowing soap scum to to build up can damage the appearance of the the system.

The enclosure using a product suggested by the producer. Check the label in your cleaning item to make sure it is secure for use on surfaces. Soft, non-abrasive gel or cream cleansers, dish soap, laundry detergent and lots of bathroom cleaners are safe for use on vinyl tub enclosures. Alternatively, home-made cleaners like a combination of water and baking soda or tri-sodium phosphate and water are secure.

Use the cleaner micro-fiber fabric, using a soft sponge or non- applicator manufactured from nylon polyethylene or polyester.

Allow cleansing items to stick to the the top of tub enclosure to get a brief time. Avoid scrubbing.

Bacteria development in the tub enclosure by occasionally sponging all surfaces using a a combination of 1/2-part water to 1/2-component chlorine bleach.

Remove any indications of mildew from silicone caulking by rubbing it using a cloth surrounding the tub enclosure dipped in to a solution of 3-elements vinegar to 1-component water.

Rinse cleansing items in the tub enclosure with water that is basic. Dry and buff using a clean micro-fiber fabric to a shine.

Metal sheds tend to cost less than wood sheds. Many are pre-fabricated and need basic onsite assembly. The steel partitions are usually slender and perhaps not suitable for to put up shelving. They’re not strong enough to to carry much weight and leaks that can damage products or personal belongings stored in the drop can be created by drilling holes in the partitions. However, you can install some boards over the partitions to brace shelves in an in a manner that that will not damage your steel drop.

Where you want to to hold the shelves measure the peak of the wall in the drop. Measure to the greatest level of shelving you want to install in the event you want a lot more than one row of shelves.

Cut a two-by-four to the peak you measured utilizing a circular saw, miter saw or handsaw.

Place the board across the drop wall where you want the shelf to start. The board should lie flat. Ask a buddy to support the the board set up. Measure the the length in the corner to the board.

Go outdoors, then to where the board should be inside the wall, calculate the the length from your corner. Drill pilot holes throughout the wall that is drop and to the board. Drill holes every 6″ across the board.

Place a washer over a 1 1/2 inch deck screw till it touches the the top of the screw. A little amount of silicone caulk over the side of the washer that can touch the steel wall.

Drive the screw through the pilot hole to the wood. Make sure that the washer is tight from the wall that is drop. It it makes a water-proof seal throughout the hole when the silicone sealant dries. Continue with all the screws.

Cut an additional board and spot it about 18-inches from the board. Drill pilot holes and mount the board as you did the first one. Continue this process with an increase of boards before the framing is long enough to to keep your shelves if desired. These boards distribute the fat saved on the shelves assisting your slender partitions hold mo Re fat.

Hold a l shaped shelf bracket onto the board a-T your preferred peak. Drive screws through the holes to to put up it in location. Place still another bracket around the board that is next, then use an amount to find out the precise height. Secure it. Continue inserting brackets on the boards that are remaining.

Place the boards of your shelves. Drive screws through the brackets’ upper holes. Alternatively, you’re able to buy A3/4inch sheet of plywood and minimize it to the shelf depth you want utilizing a tablesaw or your round observed secure the plywood utilizing screws.

The dry wall basically was not installed correctly, or you’ve got removed wall-paper if the drywall buckled and in your wall got damp, noticeable seams, valleys, ridges and residue are not an appealing sight in any area. It’s possible for you to fix it using a texturing approach that dry wall installers contact skim coating, that’s a method they use to produce partitions that are completely smooth. It requires some talent to still do it, while it will not involve complex resources and materials. You might need to invest more time on the work when compared to a professional would, in the event you are new to dry wall finishing.

Sand the wall with 120-grit sandpaper to eliminate residue or bumps from wallpaper removal. Use a pole to achieve areas that are higher or to sand the ceiling. Where the paper tape can be viewed sanding seams. Distribute a coat of PVA primer as soon as you have completed sanding and let it dry. Polyvinyl acetate is a primer-sealer that makes all the the area uniform.

Mix a batch of all purpose joint compound powder with water in a 5-gallon bucket or use ready-mixed compound. Make it the consistency of peanut-butter in the event that you combine your own. It should remain on your device without falling off and will not be pourable. Transfer some.

Spread the compound in the dry wall in to depressions and scrape it flat with a 10- to 12-inch dry wall knife. Distribute the compound on both sides of these, whether there are ridges or obvious seams and scrape it flat with all the wall. Do not attempt to make them vanish on the coat. Depending how defects that are large are they’re, it might take several coats.

Let the co mpound dry, then sand it clear the sanding take out the wall and distribute still another coat over a broader location of the wall and scrape it flat. Let it dry, sand and use a coat. The thought is to construct up the wall area till it’s as large as seam or the greatest ridge.

Keep your knife free of components of of paper and dried co mpound that is joint by eliminating particles in the mud within the trough and scraping it on the steel rim of the trough. The debris will make lines on the wall when you scrape, which you could possibly be in a position to sand off — or you may need to include an added coat to fill them.

Sand the wall lightly -grit sandpaper following the last coat dries. The wall with PVA primer before it is painted by you.

Brick veneer, whether installed indoors or outside, can make some houses seem austere and dated. Unfortunately, eliminating the veneer may be costly. It it takes a specialist, when eliminated, as it may damage the partitions significantly under the the veneer. An option that provides your house a fresh, clear, contemporary look would be to paint the veneer. Painting over brick needs the proper resources and timing for the work, but it’s a weekend task it is possible to tackle effortlessly on your own, saving yourself hundreds – if not thousands – of bucks.

Scrub away particles using a wire brush, aged peeling paint or any mineral deposits.

Wash the area completely. For a an inside area, an all purpose spray cleaner and scrub brush might suffice. For grime or stubborn stains discovered indoors or outside, combine tri-sodium phosphate scrub the wall clear and with water at ratios suggested by the producer. For exterior veneer that is really filthy, use a pressure-washer.

Allow the brick area that is cleaned to dry overnight, or for several hours. Brick veneer is porous and also you do not want to trap moisture within when you paint it over.

Protect plants and surfaces by covering them with tarps or drop cloths. Cover fixtures, like shops, trim and faucets with low-tack painter’s tape.

Prime the area using a 100-percent acrylic latex exterior or interior primer, depending upon where the brick is in your house. Cut the edges of the area using a paintbrush, and use a roller to protect the wide surfaces of your wall.

Allow the primer to dry in line with the suggestions of the manufacturer.

A coat of 100-percent acrylic paint in the colour of your selection. Choose exterior paint for outside veneer, or inside paint for in-door veneer. Use a roller for the remaining wall, as well as a brush to slice the the edging. Let it dry in accordance with the manufacturer. Generally paints dry within an hour.

Should you sense it’s necessary paint a 2nd coat on the wall.

Light fixture styles differ but electrical containers are less or more similar, and that means you generally require an adapter to to install a fixture into a box. Electricians contact this adapter a cross-bar, and a cross-bar particular to that particular fixture typically is provided in the installation package when you buy a fresh light fixture. In the event that you do not have a cross-bar for it and want to install a fixture that is antique or used, you generally can make a one function. Such all-purpose attaching one to a power box is easy, and cross-bars, which are really round, are easily accessible.

Disconnect the energy to any wires in the box. To make sure that the power is off, check the wires using a tester by keeping the lead of the tester from the uncovered end of the lead from the conclusion of the wire as well as the wire. The meter should read zero. The light should remain off in the event the tester has a mild.

Measure the the length between the two screw receptacles on the the top of box using a tape measure. Find two holes in the cross-bar that are the same length apart.

Hold the cross-bar from the box and align the holes. Drive a device screw and tighten it using a screwdriver. The screws are often given the crossbar.

Feed the wires throughout the middle hole or across the notch on the medial side of the cross-bar. Some all purpose cross-bars have a hole that is greater making it effortless after creating connections to drive wires straight back to the box. In the event the cross-bar has ahalf-inch or hole that is smaller, nevertheless, it is generally more easy to feed the wires through the greater room supplied on the perimeter.

Install a ground screw in to an obtainable hole on the crossbar in to which it suits. This provides you with a safe location to to install fixture floor wires and the circuit. Ground screws are accessible a-T any given hardware shop, and you can be given the crossbar.

When tiling a basement wall you should consider the level of moisture as well as just how much of the wall is under-ground it it has. The greatest problem is planning the wall to prevent moisture from damaging your tiles and avoiding mortar curing that is correct. Products are accessible to seal the wall and it’s essential that you simply allow extra time for his or her application while preparing this task. Patience is the trick to installing tiles that may last so long as your house does.

Preparing Concrete Partitions

Scrub walls that were concrete using a wire brush to remove particles, some other components or dirt stuck to the wall. Grind off mortar or all ridges protruding out of the wall using a grinder that is concrete. Mix four parts water with one part muriatic acid to to clean ice melt salt New Haven deposits off.

Patch cracks and fill-in gaps around electrical wires, pipes and conduit. Complete. Break off kind ties which are protruding from your wall or basis. Cut them using a torch, when they’re going to not split off flush with all the wall.

Sweep the wall to eliminate particles and dirt produced by the repairs. Dry the wall utilizing a weed burner propane torch connected to a 20-gallon tank if there are any places that are moist. Then ventilate the area and place a de-humidifier in the area for a number of days before and following installation in the event the wall isn’t noticeably damp. The water proofing membrane WOn’t bond properly into a wall that is wet.

Apply an elastomeric water-proofing membrane. Follow the manufacturer’s guidelines for the best way to mix, prime, handle trouble spots on the wall and cure the membrane.

Tile Installation

Snap a chalkline down the guts of the wall. Snap a chalk line that is second across the underside of the wall in the peak of one-floor tile from the ground.

Dry match one row of tiles over the underside of the wall. Lay out any border or attractive tiles you intend to to add to the design. Allow 1/4inch spacing between each tile for spacers. Remove any fullsize tiles which do not fit to be cut to dimensions later. Make any changes required till you’re pleased using the lay out of the tiles.

Adhesive along A3-foot-long section continuing up after dark horizontal chalkline together with the trowel and commencing in the base of the wall. Drag the fringe of of the trowel in a somewhat curved routine from your floor toward the chalk-line. The thickness of the adhesive should be the be the sam e as the thickness of the tile.

Hold one tile in an angle that is somewhat canted next to where the chalk lines intersect, and press facing the wall. Twist the tile till it’s straight and even with equally chalk lines then press it toward the wall. Install a tile that is second in specifically the sam-e way on the reverse aspect of the chalkline that is vertical. Insert spacers involving both tiles.

Install a tile that is third then the fourth spreading mo Re adhesive needed. Place an even across all tiles and ensure they’re flush. Faucet lightly having a rubber mallet to even them out, when they’re not.

Spread mo Re adhesive in the first-row over the two middle tiles. Install two tiles on each aspect of the chalkline, just above the two tiles on the 2nd row. Insert spacers between the first-row of these tiles and tiles to sustain appropriate spacing. You have six tiles on the wallin an action-like routine. Till most of the full-sized tiles are installed, continue installing the tiles in this way.

Measure the the length to the fringe of of the full-sized tile that was last installed on the row. Subtract 1/4 inch from that measurement to get the essential dimension. that is tile Transfer that measurement on a tile and mark aline on the other side of the tile at that time. Cut the tile having a tile cutter across the line. Install the tile as you did the full-sized tiles. Continue slicing and measuring tiles in this way before you’ve got completely coated the wall. Leave the wall to treatment for 2 4 hrs.

Remove the spacers involving the tiles. Prepare a little amount of mix as muchas 3 minutes can be used in by you, in accordance with package instructions.

Pack grout involving the tiles by dragging a rubber grout float across the gaps between them. Grout no more than A3-square foot location in a period. Use the edge of the float to scrape excessive grout. Wipe the surface of the tiles having a damp sponge to eliminate grout that is remaining. Grout another 3-squarefoot area utilizing the sam-e method. After 2 minutes, go straight back over each area using the moist sponge to eliminate any haze.

Mix a brand new batch of grout before you’ve got filled in every one of the gaps and carry on grouting the wall this way. Leave the grout to treatment for 2 4 hrs.

Upgrading the lights in your house is fairly painless, however in regards to changing a light fixture with two switches a number of the knowledgeable do-it-yourself-ers cringe. Big rooms with two entrances and staircases that are dark, hallways usually have two switches to to use the fixture. This can be called a three way circuit and needs a power wire to link the two switches. The mass of wires discovered in the mild fixture’s electrical box may be daunting, but in the event that you concentrate on the lights wires only, you ought to have no problems when installing a new fixture.

Remove the mild fixture’s shade in the light fixture to gain access to the light bulbs and light sockets. This may vary depending on the maker of the style as well as the fixture.

Turn off the 15- or 20-amp lighting circuit-breaker that powers the two switches as well as the light fixture. Remove the bulbs that are light in the sockets that are light.

Place a non-contact voltage sensor alongside the sockets. When the electric power is disconnected, the indicator light WOn’t illuminate.

Look in the bottom of the fixture close to the sockets for the two screws. These screws hold the light fixture to the box in the ceiling. Remove the screws, exposing the wiring and re-leasing the fixture in the ceiling.

Follow the black wire in the fixture to the wire connector. Hold the non-contact sensor alongside the connector to ensure the power is off.

Untwist the connector keeping the fixture’s black electrical wire to the black electrical wire in the ceiling box. Untwist the connector keeping the fixture’s white electrical wire to the white electrical wire in the ceiling box.

Remove the wire connector keeping the mild fixture’s green ground wire to the bare copper ground wires in the electrical box. Don’t eliminate the wire connectors within the box as these connectors total the three way relationship involving the two switches.

Follow the instructions to to put together your mild fixture that is new if assembly is essential. By twisting an orange wire connector connect the white wire in the fixture to the white wire in the box in the ceiling.

Connect the fixture’s black electrical wire from the fixture to the black electrical wire from your ceiling with a different connector. By twisting an wire connector onto the grounding wire from your fixture make the last relationship.

Position the fixture contrary to the ceiling. Use the screws offered using the fixture to to install the fixture foundation to the ceiling box that is electrical.

Install mild bulbs in your fixture that is new and connect the shade that is mild. Turn on the mild fixture’s circuit breaker supplying electricity to the threeway circuit.

By character, garages tend to become a warehouse of pentup fumes out of your car exhaust and from chemicals like pesticides and paint. These fumes that are poisonous can linger in your garage if it isn’t well-ventilated, particularly in the warmth of the summer. You will find lots of ways to ventilate your garage to allow it to be a safer location to use as a storage or function area.

Install Windows

Windows aid provide outdoors during your garage, drawing out fumes and chemicals. The finest ventilation is offered by installing two windows across from each other on walls. Open both windows to produce an air current that flows to another in one aspect of the garage, while drawing in air in the other transporting dangerous gases. This this method fails as nicely in garages that are attached because one or two partitions are joined to the home, where you can not install a window. Be cautious leaving your windows open as this might be an invitation to burglars to to analyze resources or your costly vehicle.

Window Lover

In the event you do not want to spend to install a 2nd window and currently have a window, purchase a cheap window-fan to help draw air. This could be a box-type flooring lover which you set facing an open window on a table. This is most effective if a garage-door is open, allowing the lover to pull in air that is fresh while pushing air but the fan draws air from any little resource, including gaps around a garage-door.

Roof Turbine Vents

Roof turbine vents on average are bulbous and spherical with slats that are open. They take a seat on in the wind currents at the the very top of your roof and spin, pulling up air in the garage. Although there may be installation costs involved — unless you’re a handy do-it-yourselfer — this option is costeffective for the long run because it doesn’t require electricity to power the turbine.

Static Vents

They’ve been installed in the partitions of your garage, although vents might seem comparable to air vents in your home. Install all of them using the slats angled s O that rain falls from the openings in the place of enabling rain to enter and pointing up. These function most readily useful when one is put at the top of a-wall, with all the other low on the wall that is contrary. This generates an air existing that pushes up air through the vent that is greater and pulls fresh-air through your whole garage from your vent. This is related to the thought of utilizing two windows, however you can leave the vents open evening and all day without fretting about about unauthorized entry via an open window.

Exhaust Fans

With regards to the dimension of your garage, it is possible to install a kind of exhaust fan-to assist pull fume-stuffed air from the room. Bathroom-type exhaust followers so are especially helpful in the event that you’ve got a washing-machine including dampness to the air and function in little places. Attic followers are stronger. They may be installed in the ceiling of the garage to force up air from your garage and out a vent in the roof. Another alternative that is main-stream is akitchen range hood. Choose one that vents exterior, then set it up on a-wall near to where you usually function in your garage. Even though the rangehoods are frequently noisy, they’re effective a-T removing air that is tainted.